EXPANSION BOARDS:

»AEB4-O / AEB8-O

»AEB4-I / AEB8-I
»TEB
»WCM
 

Analog Expansion Boards for Hammerfall® Series,
HDSP 9652 and DIGI96® Series

Overview Operation Technical Specs / Features Compatibility Notes Pricing
 
4 / 8 ANALOG INPUTS WITH 24 BIT AD-CONVERTERS!
 
The AEB4-I (Analog Expansion Board) adds 4 analog inputs in professional quality to all ADAT capable RME cards (see below). Level adjustment +4 dBu/-10 dBV, 107 dBA SNR and a servo balanced input circuit deliver perfect sound and sonic clarity.

The AEB4-I is designed for maximum flexibility. Both stereo inputs 1/2 3/4 are automatically copied to channels 5/6 and 7/8. Installation is done in a convenient manner using the supplied bracket, or - as no contact to any slot on the motherboard is needed - at any place inside the computer. Nuts for all TRS jacks and a drilling template are included.

The AEB8-I offers 8 inputs with 4 stereo TRS jacks. Usual insert cable can be used to split the connectors from stereo jack to mono jacks. Level adjustment +4 dBu/-10 dBV, 107 dBA SNR and highest suppression of PC-noise guarantee perfect sound quality.
OPERATING THE AEB4/8-I


Using the Analog Expansion Board is very easy to do, thanks to the clearly structured and informative Settings dialog of the RME cards. The AEB4/8-I operates like any other converter with ADAT output, but is connected internally. Therefore the card's input selector has to be set to 'Internal'.

The AEB gets its clock from the DIGI (thus works as slave.) To avoid a clock loop the card has to be switched into 'Master' mode (field 'Clock Mode'.)

The Input Status display now shows the selected input (Internal), the current sample rate (44.1/48) and format (Adat.)

 

TECHNICAL SPECIFICATIONS AND FEATURES
 
Input AEB4-I 4 x 1/4" TRS jack, servo balanced
Input AEB8-I 4 x 1/4" TRS jack, unbalanced
Dynamic ratio 104 dB (RMS unweighted), 107 dBA
THD+N -95 dB (0.0017 %)
Frequency response -0.1 dB: 10 Hz - 21 kHz
Input level for 0 dBFS @ +4 dBu: +12 dBu
Input level for 0 dBFS @ -10 dBV: +2 dBV
Crosstalk > 110 dB
Supported sample rates 32 kHz - 48 kHz
Input impedance 10 kOhm
Power supply uses 3.5" floppy connector, 12 V/5 V DC, 190 mA
AEB needs no slot on the motherboard
Standard bracket, board dimensions AEB4: 85 x 95 mm, AEB8: 120 x 95 mm
1 internal cable 2-pin, 1 internal cable 3-pin, 1 power adapter cable 5 1/4" to 2 x 3.5" included

COMPATIBILITY NOTES

HDSP 9652

Two AEBx-I and two AEBx-O or two TEB can be connected and operated simultaneously, in all possible combinations. One TEB can be used together with either one AEBx-I or AEBx-O.
 

DIGI96 SERIES

AEBs use the internal ADAT interface of the DIGI cards. Therefore they do not work with the DIGI96 (which did not support ADAT.) To operate the AEB4-I and AEB8-I the used DIGIs must have the connectors ST6/7 on board (for the Word Clock Module.) These were not present on the very first cards of the DIGI96 series (1998 to beginning of 1999.)

One AEBx-I and one AEBx-O can be connected and operated simultaneously, in all possible combinations. Or one TEB.
 

HAMMERFALL DSP MULTIFACE / DIGIFACE

Multiface and Digiface use the Hammerfall DSP PCI card. This card has no internal inputs or outputs. Therefore no Expansion Boards can be used.
 

HAMMERFALL SERIES

An operation with the Hammerfall or Hammerfall Light requires board revision 1.5 or higher, because the internal connectors ADAT1Out, ADAT2Out and ST7 were not implemented in earlier versions.

One AEBx-I and two AEBx-O can be connected and operated simultaneously, in all possible combinations. Or one TEB and one AEBx-O.
 

MANUFACTURER'S SUGGESTED RETAIL PRICING

 See your local distributor's website for current price information.

Home    News    Audio Converters    Sound Cards    MADI Series     DIGICheck   Mic Preamps
Accessories    Support    RME Newsgroup    Company Info    Purchasing    Downloads    Links

Copyright 2002 RME. All rights reserved. RME is a registered trademark.
This website contains names and marks of other companies.